Large "Corvette" servo for a stronger 2nd gear. Performance separator plate for quicker shifts. All necessary gaskets and seals included. Line pressure booster kits for better clutch holding power.Accumulator parts that do not require unusual modifications and still provide firm shifts. Aluminum accumulator pistons to replace "usually damaged" plastic pistons. Performance accumulator check valve that will allow more 3rd clutch apply oil without creating "shift overlap". Easy to follow detailed instructions. Valve body removal is required, instructions for valve body R&R included.
Works with factory engineered design to provide increased durability and a performance shift feel. When building a high performance 4L60E transmission the first question usually ask is, what type shift improvement kit should I use? At Trutech Performance Transmissions our ASE Master Technicians backed by years of transmission repair experience and training researched this issue. We have studied the operation of this transmission and determined what modifications will actually improve shift performance and give a long service life.In most shift improvement kits on the market two areas are commonly targeted for modification. These being accumulators and the separator plate. Understanding the operation of the automatic transmission we knew that modification to these parts would create a firmer quicker shift feel but would do nothing to improve the operation or increase durability of the transmission. We will attempt to unravel some of the mystery of shift calibration in this guide. In the automatic transmission an accumulator's function does as it's name implies, it accumulates or absorbs fluid in a clutch apply circuit and normally uses a spring loaded piston to cushion the apply of a clutch or band. Without an accumulator in the apply fluid circuit, the rapid buildup of fluid pressure would cause the clutch or band to apply very quickly and create a harsh or "bang" shift. The separator plate has small orifices that regulate the rate of apply fluid into the apply circuit. This orifice diameter has a direct effect on shift timing of the apply components. The larger the orifice the more fluid that will pass creating a quicker apply. It is easy to understand how modifying these two areas can change shift feel. At Trutech we looked beyond shift "feel" to determine what modifications would improve transmission performance and durability. Issues we have found with drilling holes too large in the separator plate is that it creates a shift overlap of apply components at certain RPM ranges.
Shift overlap occurs when two apply components are applied at the same time. Shift overlap greatly decreases the apply component life because the components work against each other. Blocking or modifying fluid passages in the accumulators also have an adverse affect, the rapid apply of the apply component causes a jolting effect on both the apply components and the hard parts inside the transmission. If severe enough this jolting can cause broken internal parts. The 1-2 accumulator piston and spring setup was redesigned by the factory in 1994.
This was done because the accumulator spring normally broke or caused damage to the separator plate. The redesign was an inexpensive solution to the problem. The Trutech Shift Module contains heavier accumulator springs to slightly increase the rate of apply to the friction components.We also have you convert the 1-2 accumulator piston back to the pre-1994 setup and we supply a heavy duty plate to use between the spring and the separator plate to protect it from damage. This arrangement provides a performance shift feel without the damaging effect of a "bang" shift. We provide heavier springs for the 3rd accumulator and 3-4 accumulator but we do not recommend any modification that will make the accumulators inoperative. Our Modules contain new accumulator pistons to restore hydraulic intregrity to your transmission. The pistons are common areas of fluid bypass.
At Trutech we were interested in improving the holding ability of the apply components. In an automatic transmission the diameter of the servos determine in a large part how well a band will hold. As with any hydraulic component the larger the apply area the more efficient the component. In other words, larger servos mean better band holding efficiency. On the other hand, in the 4L60E the servo size plays a large part in shift timing.
These "super servos" depend a large part on the servo return spring to release the band when changing to the 3rd gear range. Racing applications are operated at wide open throttle and rarely downshift, these racing transmissions benefit from the larger servos. The 4L60 type transmission hydraulic design does not exhaust an apply circuit once applied as it shifts through all forward gear ranges. The servo diameter and servo return spring determine timing of band release in the 2-3 shift when the 3rd accumulator circuit is filled.Modifications to the circuit apply orfices in the separator plate are good modifications as long as down shifting and low RPM operation are not factors. Racing transmissions have a certain amount of "shift overlap" at lower RPM ranges. Racing recommended servos and "shift kits" should not be used in street driven transmissions because this lower RPM overlap will cause early transmission failure. Our shift module has a performance servo combination that works and provides excellent band holding ability in a street driven transmissions.
The increase in servo size also has an effect on shift feel. Our servo combination provides a firm crisp shift. There is a direct relation between the 1-2 accumulator, accumulator valve and the 2nd servo. We have included a performance accumulator valve in our Performance Shift Module. We also provide a performance calibrated separator plate with gaskets.This plate has a performance factory shift calibration. Because a common failure in the 4L60E transmission is the 3-4 clutch we have modified the apply orifice to the 3-4 apply circuit, allowing fluid into the apply circuit at an increased rate.
To prevent shift timing issues in the 2-3 or 3-2 shift we have included a metered check valve for the 3rd accumulator circuit. Removal of the valve body will be required and the use of an inch pound torque wrench will be needed for reassembly.
The transmission line pressure is increased with the addition of a large diameter boost valve and heavier pressure regulator valve spring. Increased line pressure will provide higher pressures for better apply component holding capability. The line pressure increases as the accelerator pedal position and engine torque increases. With the Trutech Performance Shift Module we took a completely different approach to transmission performance than that of other manufacture's shift improvement kits.
We do not claim to correct problems caused by wear. The only correction for a wear related issue is part replacement or the part must be remanufactured back to factory specification. Our Shift Module works with the factory engineered design. The parts provided in this Shift Module are of the highest quality.
No special tools are required and installation can be preformed with the transmission in the vehicle. The Trutech Shift Module can be installed with the transmission in the vehicle. It will require removal of the valve body.
Detailed instructions will be included on valve body removal and installation. Instructions for installation of the module parts will also be included. This Shift Module is more comprehensive than anything offered on the market. This is a very complete performance parts kit to recalibrate and improve the shift performance and increase the service life of your street/strip driven transmission.Simple hand tools and an inch pound torque wrench will be required. Thank you for choosing Trutech Performance Transmissions for your performance transmission needs. This is a free service provided to our customers. All questions will be answered within 24 hours. Thank you for choosing Trutech Performance Transmissions.
For high performance applications we offer our Performance Shift Module. Our Performance Shift Module contains additional valves, a billet 4th servo and pinless accumulator pistons.These parts are designed to increase operating pressure, clutch and band holding power to improve performance and life of your transmission. Visit our store pages for technical information on transmission repair and modifications. We believe in sharing our knowledge and experience with our customers.
Our goal is to provide our customers with the information needed to choose the correct parts for thier transmission application. Get valuable technical information by viewing our tech pages. They are accessible from the left column of any store page.
Your satisfaction and feedback is a very important part of our business. Your satisfaction is our top priority! You can call this number between the hours 10:00 a. Toll free number is for U.For calls from outside U. Procare Performance Transmissions and Trutech Performance Transmissions are sister companies. We have the same policies and ideals.
Trutech Transmissions custom builds transmissions in Enterprise, Al.. Our website, Trutech Performance Transmissions , is an information packed website we are updating daily. The item "Trutech Level 2 High Performance Pro Street Shift Module Kit 1995 4L60E" is in sale since Thursday, September 15, 2011. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Transmission & Drivetrain\Automatic Transmission & Parts\Automatic Transmission Parts".
The seller is "trutechtrans" and is located in Enterprise, Alabama. This item can be shipped worldwide.